Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing COD - (unfzu) - Axl Harmon

Friday, May 7, 2021

Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing COD - (unfzu)

Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing
COD

Download Now
Server 1
Download Now
Server 2
Download Now
Server 3


Notes: Don't make the antenna plug get touch with the Motor solder pins, otherwise it would burnt the ESC.


Description:

Brand: Happymodel

Model: CrazyF4 ELRS

Item Name:  F4 Flight Controller AIO 5A ESC 5.8G VTX ELRS Receiver 5-in-1 Board


Flight controller

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)

Sensor: MPU-6000(SPI connection)

Original whoop size compatible

Power supply: 1S battery input (DC 2.9V-4.35V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready

Built-in Betaflight OSD(SPI Control)

Built-in 5.8G VTX

Built-in Serial-based ExpressLRS 900MHz receiver(915MHz or 868MHz optional)

Built-in 5V 1A BEC

Flight controller firmware target: CRAZYBEEF4DX

Onboard 4in1 ESC

MCU upgraded to EFM8BB21

Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)

Support BLHeliSuite programmable

Factory firmware: O_H_5_REV16_8.HEX

Default protocol: DSHOT600

Onboard Serial-based ELRS Receiver

Operation current: ~100Ma

Rx To FC protocol: CSRF

RF Frequency optional: 915mhz or 868mhz(EU)

Antenna connector:  IPEX4

Telemetry output Power: <17dBmFirmware target: Happymodel_RX_ES915RX

Receiver protocol: CRSF

Could bind with Happymodel ES915TX , Frsky R9M and DIY ELRS TX module(need to flash the same version ELRS firmware)

Firmware flash via Betaflight pass-through

Onboard 5.8g VTX

Output power: 25mw~200mw switchable

Frequency: 40CH

Input voltage: 3.3V-5.5V

Current consumption: 300mA(type)

Frequency: 5.8GHz 5bands 40 channels(include Race band)Smartaudio ready

Onboard voltage and Amperage meters  settings

Voltage meter scale setting 110

Amperage meter scale setting 1175


Bind Procedure:

1. Supply power to CrazyF4 ELRS flight controller (Plug the USB), wait until the RX LED is off, immediately turn off the power (Unplug the USB), and then repeat the above steps again. When the RX is powered on for the third time, the LED light will start to double-flash, which means that the RX enters into the binding mode


2. Insert the ES915TX module or other DIY 2.4G ELRS TX to your OpenTX Radio transmitter, and choose External RF mode to CRSF protocol, then you can find ELRS menu from the Radio system (Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into ELRS and press [Bind], the RX LED on the Flight controller will getting to be solid if bind successfully.


3. Receiver LED status meanings:LED solid means bind successful or Connection established; LED double-flash means in bind mode; LED flash slowly means no signal established with the TX module


Package Included:

1x CrazyF4 5-IN-1 Flight Controller Board






Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing
COD
Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing COD



Happymodel CrazyF4 ELRS AIO 5in1 F4 Flight Controller Built-in 5A ESC 5.8G VTX and ELRS Receiver for RC Drone FPV Racing COD


@way2themes